Exit
SearchSearch
1011 Athens Street
Gainesville, GA 30501 USA
Gainesville Industrial Electric
Request Information
Global Max WPI
AMHGTK, NEMA Premium, Medium Voltage
Unit of Measure

Specifications

Brands

 N/A TECO

Power

 N/A 200 hp
Speed1 N/A 900 rpm

Frame Number

 N/A 5009B

Full Load Efficiency

 N/A 93.5 %

Full Load Power Factor

 N/A 73.0 %

Full Load Ampere at 2300 Volt (V) Voltage

 N/A 55.0 A

Approximate Shipping Weight

 N/A 3,550 lb

Enclosure

 N/A Weather Protected Type I (WPI), (IP23)

Voltage

 N/A 2300 V4000 V

Phase

 N/A Three

Frequency

 N/A 60 Hz

Continuous Service Factor for 60 Hertz (Hz) Frequency

 N/A 1.15
Ambient Temperature2 N/A 40 ºC
Elevation3 N/A 3300 ft

Shaft Material

 N/A 1045 Carbon Steel

Industry Standards and Approval

 N/A Canadian Standards Association (CSA) NEMA Premium

Applications

Applications

 N/A
  • Pumps
  • Fans and Blowers
  • Compressors

Features

Features

 N/A
  • Standard Features: 100 Ohm Platinum Stator RTD's (2 per Phase), Space Heaters (120V)
  • Standard Features: Pre-Drilled & Plugged Bearing Bracket for 100 Ohm Platinum Bearing RTD's on 5000 Frames & Above
  • Standard Features: Pre-Drilled & Spot Faced on Top of End Bracket for Vibration Detectors on 5000 Frames and Above
  • Class F Insulation
  • Class B Temperature Rise
  • NEMA Design B Torques
  • Oversized Main Conduit Box Rotatable in 90 Degree Increments Fully Gasketed with NPT Threaded Entrance - F1 Mounted
  • Rotation: F#449-449: Bi-Directional. F#5000-5813: Bi-Directional on 4,6,8P, Except 2P, which is Unidirectional, Counter-Clockwise (CCW) facing the Drive End
  • Aluminum Die Cast Squirrel Cage Rotor Construction for F#449T and Below
  • Squirrel Cage Copper or Copper Alloy Bar Rotor Construction for F#5000 and Larger
  • Paint System: Phenolic Rust Proof Base Plus Polyurethane Top Coat
  • Paint Color: Dark Gray - Munsell 7.5B 3.5/0.5
  • High Quality Ball (or Roller) Bearings Regreasable with Mobil PolyrexTM EM
  • Insulated Non-Drive End Bearing on 3600 RPM Motors; 600 HP and Larger
  • Metal Flinger on Both Ends
  • Cast Iron Inner and Outer Bearing Caps
  • Grounding Terminal Inside Main Box and on Motor Foot
  • Stainless Steel Nameplate
  • Suitable for Inverter Use per NEMA MG-1 Part 31.4.4.2
    • Motor service factor is 1.0 when operated on a VFD.
    • Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1. Part 31. An isolation transformer or other method of mitigating common mode voltages from motor terminals must be utilized. Please refer to page 184 to check out our accompanying TeamMasterTM starters
    Inverter Duty Speed Range: 20:1 Variable Torque, 10:1 Constant Torque (350 HP and Larger are 3:1 Constant Torque)
  • 6 Leads, Wye Delta Capable
  • Motors are CSA Approved
  • 2-Pole motors, 600HP and larger, are Form Wound and Insulated Non-Drive End Bearing
  • Spotface 1/4 -28UNF Tap x 12mm Deep on Top of Both End Brackets with VB300 Vibration Sensor on 5000 Frames and Larger

Note

Note

 N/A Data subject to change without notice.
All motors are NEMA B torque.
F#5012 dual drilled for 5012/11 mounting holes.
  • 1 Slower speeds available as Made to Order.
  • 2 Consult a Stock Product Application Specialist for suitability in higher ambient environments, and for variable and constant torque speed ranges.
  • 3 Consult a Stock Product Application Specialist for suitability at higher elevations.
Copyright © 2024 Gainesville Industrial Electric Co., All Rights Reserved   Site created by Thomas Web Solutions and Powered by Navigator Platform