Exit
SearchSearch
1011 Athens Street
Gainesville, GA 30501 USA
Gainesville Industrial Electric
Request Information
AEEAGD, EPACT Design C, Low Voltage Crusher Duty
Unit of Measure

Specifications

Brands

 N/A TECO

Power

 N/A 300 hp

Speed

 N/A 900 rpm

Frame Number

 N/A 5806C

Full Load Efficiency

 N/A 94.5 %

Full Load Power Factor

 N/A 81.0 %

Full Load Ampere at 230 Volt (V)

 N/A 367 A

Approximate Shipping Weight

 N/A 5,093 lb

Enclosure

 N/A Totally Enclosed Fan Cooled (IP55)
Voltage1 N/A 460 V

Phase

 N/A Three

Frequency

 N/A 50 Hz60 Hz

Continuous Service Factor for 60 Hertz (Hz) Frequency

 N/A 1.15

Continuous Service Factor for 50 Hertz (Hz) Frequency

 N/A 1.0
Ambient Temperature2 N/A 40 ºC
Elevation3 N/A 3300 ft

Shaft Material

 N/A High Strength 4140 AISI Steel Shaft

Certification

 N/A Canadian Standards Association (CSA) ee CC002A European Conformity (CE) NEMA Premium Underwriters Laboratories (UL)

Applications

Applications

 N/A
  • Crushers
  • Ball Mills/Rolling Mills
  • Impactors
  • Any High Torque Application
  • Chippers/Shredders

Features

Features

 N/A
  • Class F Insulation
  • Class B Temperature Rise
  • NEMA Design C Torques; Equal or Greater Than
  • Class F Insulation
  • Class B Temperature Rise
  • NEMA Design C Torques; Equal or Greater Than 200% Starting Torque/250% Breakdown Torque
  • Cast Iron Frame, End Brackets; Pressed Steel Plate Main Conduit Box and Fan Cover
  • Cast Iron Main Conduit Box of 505UZ Frame
  • Grounding Terminal Inside Main Conduit Box with additional Foot Grounding Provision
  • Oversized Main Conduit Box Rotatable in 90 Degree Increments - F1 Mounted
  • Bi-Directional Rotation
  • Aluminum Die Cast Squirrel Cage Rotor Construction
  • Paint System: Phenolic Rust Proof Base Plus Polyurethane Top Coat
  • Paint Color: Dark Gray - Munsell 7.5 BG 3.5/0.5
  • High Quality Ball (or Roller) Bearings Regreasable with Mobil Polyrex™ EM
  • Automatic Grease Discharge Fittings
  • Metal Flinger on Both Ends
  • Cast Iron Inner and Outer Bearing Caps
  • Stainless Steel Nameplate
  • Suitable for Inverter Use per NEMA MG-1 Part 31.4.4.2
    • Motor service factor is 1.0 when operated on a VFD.
    • Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1. Part 31.
  • Inverter Duty Speed Range: 3:1 Constant Torque
  • 6 Leads
  • Standard With Thermistors (PTC 140°C) 1 per Phase
  • Locknut and Washer on NDE for Vertical Shaft Down Applications
  • Drain Holes/Plugs on Both End Brackets for Vertical Applications
  • Threaded One Way Breather Drains for Horizontal Mount Applications
  • Motors are CSA Approved
  • Spotface 1/4-28UNF Tap x 12mm Deep on Top of Both End Brackets with VB300 Vibration Sensor on 5000 Frames and Larger

Note

Note

 N/A Per DOE regulations, the smaller frame non-exempt High Efficiency inventory was obsoleted in June 2018, and only has minimal inventory.

Data subject to change without notice.
  • 1 575 V motors available on a made-to order basis. Consult a Stock Product Application Specialist for details.
  • 2 Consult a Stock Product Application Specialist for suitability in higher ambient environments.
  • 3 Consult a Stock Product Application Specialist for suitability at higher elevations.
Copyright © 2024 Gainesville Industrial Electric Co., All Rights Reserved   Site created by Thomas Web Solutions and Powered by Navigator Platform