Gainesville Industrial Electric Co. - PG Global Series NEMA Premium, Three Phase, Medium Voltage Motors

Unit of Measure

Items	PG1002 PG Global Series 100 Horsepower (hp), 3600 Revolutions Per Minute (rpm), and 447TS Frame Three Phase NEMA Premium Efficiency Medium Voltage Motor	PG1004 PG Global Series 100 Horsepower (hp), 1800 Revolutions Per Minute (rpm), and 447T Frame Three Phase NEMA Premium Efficiency Medium Voltage Motor	PG1006 PG Global Series 100 Horsepower (hp), 1200 Revolutions Per Minute (rpm), and 447T Frame Three Phase NEMA Premium Efficiency Medium Voltage Motor	PG1008 PG Global Series 100 Horsepower (hp), 900 Revolutions Per Minute (rpm), and 447T Frame Three Phase NEMA Premium Efficiency Medium Voltage Motor	PG1252 PG Global Series 125 Horsepower (hp), 3600 Revolutions Per Minute (rpm), and 447TS Frame Three Phase NEMA Premium Efficiency Medium Voltage Motor
Description	N/A Global Max WPI AMHGTK, NEMA Premium, Medium Voltage
Brands	N/A TECO
Power	N/A 100 hp	N/A 100 hp	N/A 100 hp	N/A 100 hp	N/A 125 hp
Speed¹	N/A 3600 rpm	N/A 1800 rpm	N/A 1200 rpm	N/A 900 rpm	N/A 3600 rpm
Frame Number	N/A 447TS	N/A 447T	N/A 447T	N/A 447T	N/A 447TS
Full Load Efficiency	N/A 92.0 %	N/A 93.7 %	N/A 94.6 %	N/A 93.2 %	N/A 93.1 %
Full Load Power Factor	N/A 87.2 %	N/A 82.5 %	N/A 78.1 %	N/A 74.9 %	N/A 88.4 %
Full Load Ampere at 2300 Volt (V) Voltage	N/A 23.0 A	N/A 24.0 A	N/A 25.0 A	N/A 27.0 A	N/A 28.0 A
Approximate Shipping Weight	N/A 1,760 lb	N/A 2,050 lb	N/A 1,920 lb	N/A 2,310 lb	N/A 1,800 lb
Enclosure	N/A Weather Protected Type I (WPI), (IP23)
Voltage	N/A 2300 V4000 V
Phase	N/A Three
Frequency	N/A 60 Hz
Continuous Service Factor for 60 Hertz (Hz) Frequency	N/A 1.15
Ambient Temperature²	N/A 40 ºC
Elevation³	N/A 3300 ft
Shaft Material	N/A 1045 Carbon Steel
Applications	N/A Pumps Fans and Blowers Compressors
Features	N/A Standard Features: 100 Ohm Platinum Stator RTD's (2 per Phase), Space Heaters (120V) Standard Features: Pre-Drilled & Plugged Bearing Bracket for 100 Ohm Platinum Bearing RTD's on 5000 Frames & Above Standard Features: Pre-Drilled & Spot Faced on Top of End Bracket for Vibration Detectors on 5000 Frames and Above Class F Insulation Class B Temperature Rise NEMA Design B Torques Oversized Main Conduit Box Rotatable in 90 Degree Increments Fully Gasketed with NPT Threaded Entrance - F1 Mounted Rotation: F#449-449: Bi-Directional. F#5000-5813: Bi-Directional on 4,6,8P, Except 2P, which is Unidirectional, Counter-Clockwise (CCW) facing the Drive End Aluminum Die Cast Squirrel Cage Rotor Construction for F#449T and Below Squirrel Cage Copper or Copper Alloy Bar Rotor Construction for F#5000 and Larger Paint System: Phenolic Rust Proof Base Plus Polyurethane Top Coat Paint Color: Dark Gray - Munsell 7.5B 3.5/0.5 High Quality Ball (or Roller) Bearings Regreasable with Mobil PolyrexTM EM Insulated Non-Drive End Bearing on 3600 RPM Motors; 600 HP and Larger Metal Flinger on Both Ends Cast Iron Inner and Outer Bearing Caps Grounding Terminal Inside Main Box and on Motor Foot Stainless Steel Nameplate Suitable for Inverter Use per NEMA MG-1 Part 31.4.4.2 Motor service factor is 1.0 when operated on a VFD. Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1. Part 31. An isolation transformer or other method of mitigating common mode voltages from motor terminals must be utilized. Please refer to page 184 to check out our accompanying TeamMasterTM starters Inverter Duty Speed Range: 20:1 Variable Torque, 10:1 Constant Torque (350 HP and Larger are 3:1 Constant Torque) 6 Leads, Wye Delta Capable Motors are CSA Approved 2-Pole motors, 600HP and larger, are Form Wound and Insulated Non-Drive End Bearing Spotface 1/4 -28UNF Tap x 12mm Deep on Top of Both End Brackets with VB300 Vibration Sensor on 5000 Frames and Larger
Note	N/A Data subject to change without notice. All motors are NEMA B torque. F#5012 dual drilled for 5012/11 mounting holes.
Industry Standards and Approval	N/A Canadian Standards Association (CSA) NEMA Premium
¹ Slower speeds available as Made to Order. ² Consult a Stock Product Application Specialist for suitability in higher ambient environments, and for variable and constant torque speed ranges. ³ Consult a Stock Product Application Specialist for suitability at higher elevations.