Gainesville Industrial Electric Co.
Gainesville Industrial Electric Co.
1011 Athens Street
Gainesville, GA 30501

Toll Free: 1-800-457-6210
Local : 770-532-4411
Fax : 770-532-4496
Email: sales@anametelectrical.com
Website: www.gainesvilleindustrial.com
Print Back
AFHP, TEFC, NEMA Premium Efficiency, Medium Voltage
Unit of Measure

Specifications

Brands

 N/A TECO

Power

 N/A 300 hp

Speed

 N/A 1800 rpm

Frame Number

 N/A 5007/9B

Full Load Efficiency

 N/A 95.0 %

Full Load Power Factor

 N/A 86.1 %

Full Load Ampere at 2300 Volt (V) Voltage

 N/A 38.0 A

Approximate Shipping Weight

 N/A 3,580 lb

Enclosure

 N/A Totally Enclosed Fan Cooled (IP55)

Voltage

 N/A 2300 V4000 V

Phase

 N/A Three

Industry Standards and Approval

 N/A Canadian Standards Association (CSA) NEMA Premium

Frequency

 N/A 60 Hz

Inverter Duty

 N/A 10:1 Variable Torque, 3:1 Constant Torque

Continuous Service Factor for 60 Hertz (Hz) Frequency

 N/A 1.15
Ambient Temperature1 N/A 40 ºC
Elevation2 N/A 3300 ft

Shaft Material

 N/A 1045 Carbon Steel

Applications

Applications

 N/A
  • Fans and Blowers
  • Compressors
  • Severe Duty/Petro-Chem
  • Pumps
  • Mixers
  • Pulp and Paper Application
  • Crushers
  • Conveyors

Features

Features

 N/A
  • CSA Certified for Class I, Div. 2, Group A, B, C, D - Temp Code T2B Minimum
  • CSA Certified for Class II, Div. 2, Group F & G - T3C Minimum
  • Standard Features: Provisions for Bearing RTD's, 100 Ohm Platinum Stator RTD's(2/Phase), Space Heaters(120V)
  • Class F Insulation
  • Class B Temperature Rise
  • NEMA Design B Torques
  • Oversized Fabricated Steel Main Conduit Box Rotatable in 90 Degree Increments Fully Gasketed with NPT Threaded Entrance - F1 Mounted, Field Convertible to F2 and F3
  • Bi-Directional Rotation; except 2 Pole which is Counter-Clockwise (CCW) facing the Drive End
  • Cast Iron Frame and End Brackets
  • Aluminum Die Cast Squirrel Cage Rotor Construction or Copper Bar Rotor Construction
  • Paint System: 2 Part Epoxy
  • Paint Color: Dark Gray - Munsell 7.5B 3.5/0.5
  • IEEE 841 Ready
  • Grounding Terminal Inside Main Conduit Box with additional Foot Grounding Provision
  • Test Report with Vibration Data Shipped with motor
  • High Quality Ball (or Roller) Bearings Regreasable with Mobil PolyrexTM EM
  • Bronze Metal Flinger on Both Ends
  • Cast Iron Inner and Outer Bearing Caps
  • Grounding Terminal Inside Main Box and on Motor Foot
  • Stainless Steel Nameplate and Hardware
  • Stainless Steel Breather Drain
  • Vibration Not to Exceed 0.08 Inches Per Second
  • Noise Level Not to Exceed 85 dB(A) at 1 Meter Unloaded
  • 6 Leads, with Solderless Lug Terminals
  • Motors are CSA Approved
  • Suitable for Inverter Use per NEMA MG-1 Part 31.4.4.2
    • Motor service factor is 1.0 when operated on a VFD.
    • Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1.Part 31. An isolation transformer or other method of mitigating common mode voltages from motor terminals must be utilized.
  • Spotface 1/4-28UNF Tap x 12mm Deep on Top of Both End Brackets with VB300 Vibration Sensor on 5000 Frames and Larger.

Note

Note

 N/A Insulated non-drive end bearing as standard. Motors are unidirectional, with counter clockwise rotation, facing the drive end, to change please consult factory.
Data subject to change without notice.
Motor service factor is 1.0 when operated on a VFD.
Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1.Part 31. An isolation transformer or other method of mitigating common mode voltages from motor terminals must be utilized. Please refer to page XXX to check out our accompanying TeamMaster TM starters.
  • 1 Consult a Stock Product Application Specialist for suitability in higher ambient environments, and for variable and constant torque speed ranges.
  • 2 Consult a Stock Product Application Specialist for suitability at higher elevations.