Gainesville Industrial Electric Co.
Gainesville Industrial Electric Co.
1011 Athens Street
Gainesville, GA 30501

Toll Free: 1-800-457-6210
Local : 770-532-4411
Fax : 770-532-4496
Email: sales@anametelectrical.com
Website: www.gainesvilleindustrial.com
Print Back
MAX-E2/841® Vertical Round Body Solid Shaft High Thrust with "P" Base - Low Voltage

AEUH8BDP, NEMA Premium
Unit of Measure

Specifications

Brands

 N/A TECO

Power

 N/A 10 hp

Speed

 N/A 1200 rpm

Frame Number

 N/A 256LP

Full Load Efficiency

 N/A 91.0 %

Full Load Power Factor

 N/A 80.5 %

Full Load Ampere at 230 Volt (V)

 N/A 12.8 A

Down Thrust

 N/A 110 lb

Dimension AG

 N/A 27.8 in

Approximate Shipping Weight

 N/A 380 lb

Enclosure

 N/A Totally Enclosed Fan Cooled (IP55)
Voltage1 N/A 460 V

Phase

 N/A Three

Frequency

 N/A 50 Hz60 Hz

Continuous Service Factor for 60 Hertz (Hz) Frequency

 N/A 1.15

Continuous Service Factor for 50 Hertz (Hz) Frequency

 N/A 1.0
Ambient Temperature2 N/A 40 ºC
Elevation3 N/A 3300 ft

Shaft Material

 N/A 1045 Carbon Steel Shaft, LP Mounting

Certification

 N/A Canadian Standards Association (CSA) ee CC002A National Electrical Manufacturers Association (NEMA) Premium Underwriters Laboratories (UL)

Applications

Applications

 N/A
  • Centrifugal Pumps
  • Petro-Chemical
  • Water/Wastewater
  • Pulp and Paper

Features

Features

 N/A
  • CSA Certified for Class I, Div. 2, Groups B, C, D - Temp Code T3 Minimum
  • Meets or Exceeds IEEE 841 Standards
  • Extended Warranty - 60 Months from Date of Manufacture
  • Class F Insulation
  • Class B Temperature Rise
  • NEMA Design B Torques as a Minimum; Various Ratings also Meet Design C
  • Cast Iron Frame, End Brackets, Fan Cover, Drip Cover and Main Conduit Box
  • Grounding Terminal Inside Main Conduit Box with additional Foot Grounding Provision
  • Oversized Main Conduit Box Rotatable in 90 Degree Increments - F1 Mounted
  • Bi-Directional Rotation
  • Aluminum Die Cast Squirrel Cage Rotor Construction
  • Paint System: 2 Part Epoxy
  • Paint Color: Blue - Munsell 5PB 3/8
  • Guide Bearings: Re-Greasable Single Shielded with Mobil Polyrex™ EM
  • Thrust Bearings: Re-Greasable Double Stack Angular Contact with Mobil Polyrex™ EM
  • Automatic Grease Discharge Fittings
  • Cast Iron Inner and Outer Bearing Caps for all frames
  • VBXX INPRO™ Seals Installed on Both Ends
  • Stainless Steel Nameplate and Hardware
  • Stainless Steel Automatic Breather Drain (Located at both End Brackets for Vertical Mounts)
  • Dual Column Design Nameplate as Standard (60/50 Hz)
  • Suitable for Inverter Use per NEMA MG-1.4.4.2, Part 31.
    • Motor service factor is 1.0 when operated on a VFD
    • Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1. Part 31.
  • Inverter Duty Speed Range: 20:1 Variable Torque, 10:1 Constant Torque
  • Motors are U.L., CSA Approved
  • 3 Leads Only
  • Vibration Not to Exceed 0.08 Inches Per Second
  • Noise Level Not to Exceed 85 dB(A) at 1 Meter Unloaded
  • NEMA Type P Base With LP Shaft

Note

Note

 N/A Data subject to change without notice.
  • 1 575 V motors available

    Motors 7.5 HP & up are suitable for wye/delta starting.
  • 2 Consult a Stock Product Application Specialist for suitability in higher ambient environments.
  • 3 Consult a Stock Product Application Specialist for suitability at higher elevations.